I​p​e​r​f​详​细​使​用​方​法

2014/07/01 17:18
阅读数 269

Iperf是一个网络性能测试工具。可以测试TCP和UDP带宽质量,可以测量最大TCP带宽,具有多种参数和UDP特性,可以报告带宽,延迟抖动和数据包丢失。Iperf在linux和windows平台均有二进制版本供自由使用。

 

Iperf was developed by NLANRDAST as a modern alternative for measuring maximum TCP and UDP bandwidth performance. Iperf allows the tuning of various parameters and UDP characteristics. Iperf reports bandwidth, delay jitter, datagram loss. 

 

Iperf使用方法与参数说明

 

参数说明

-s 以server模式启动,eg:iperf -s

-c host以client模式启动,host是server端地址,eg:iperf -c 222.35.11.23

 

通用参数

-f [kmKM] 分别表示以Kbits, Mbits, KBytes, MBytes显示报告,默认以Mbits为单位,eg:iperf -c 222.35.11.23 -f K

-i sec 以秒为单位显示报告间隔,eg:iperf -c 222.35.11.23 -i 2

-l 缓冲区大小,默认是8KB,eg:iperf -c 222.35.11.23 -l 16

-m 显示tcp最大mtu值

-o 将报告和错误信息输出到文件eg:iperf -c 222.35.11.23 -o ciperflog.txt

-p 指定服务器端使用的端口或客户端所连接的端口eg:iperf -s -p 9999;iperf -c 222.35.11.23 -p 9999

-u 使用udp协议

-w 指定TCP窗口大小,默认是8KB

-B 绑定一个主机地址或接口(当主机有多个地址或接口时使用该参数)

-C 兼容旧版本(当server端和client端版本不一样时使用)

-M 设定TCP数据包的最大mtu值

-N 设定TCP不延时

-V 传输ipv6数据包

 

server专用参数

-D 以服务方式运行iperf,eg:iperf -s -D

-R 停止iperf服务,针对-D,eg:iperf -s -R

 

client端专用参数

-d 同时进行双向传输测试

-n 指定传输的字节数,eg:iperf -c 222.35.11.23 -n 100000

-r 单独进行双向传输测试

-t 测试时间,默认10秒,eg:iperf -c 222.35.11.23 -t 5

-F 指定需要传输的文件

-T 指定ttl值

 

应用实例

使用 iperf -s 命令将 Iperf 启动为 server 模式,在客户机上使用 iperf -c启动client模式。

iperf –s

------------------------------------------------------------

Server listening on TCP port 5001

TCP window size: 8.00 KByte (default)

------------------------------------------------------------

 

iperf -c 59.128.103.56

上面使用服务端和客户端的默认设置进行测试

 

iperf -s -w 300K

------------------------------------------------------------

Server listening on TCP port 5001

TCP window size: 300 KByte

------------------------------------------------------------

 

iperf -c 59.128.103.56 -f K -i 2 -w 300K

      设定报告间隔为2秒,服务器端和客户端的TCP窗口都开到300KB

 

iperf -c 59.128.103.56 -f K -i 2 -w 300K –n 1000000

测试传输约1MB数据

 

iperf -c 59.128.103.56 -f K -i 2 -w 300K –t 36

测试持续36秒

 

iperf -c 59.128.103.56 -f K -i 2 -w 300K -n 10400000 –d

测试双向的传输

 

iperf -c 59.128.103.56 -f K -i 2 -w 300K –u

UDP测试

 

其中 -i 参数的含义是周期性报告的时间间隔(interval),单位为秒;在上面的例子中,表示每隔2秒报告一次带宽等信息。

 

启动一个iperf服务器进程

  首先要介绍的命令用来启动iperf服务器监听进程以便监听客户端连接的。命令如下:

  iperf.exe -s -P 2 -i 5 -p 5999 -f k

  这个命令会启动iperf,后续参数用来设定监听5999 端口(默认端口是5001), 限定iperf只允许两个连接,每5秒汇报一次连接情况。连接限制参数(-P参数)非常重要,当两个连接建立后,服务器进程就会退出。如果这个参数设定为0,那么iperf 进程将持续监听端口,并且不限制连接数量。在 Windows主机上键入该命令,会显示出如图A所示界面

  图 A


简单的iperf命令 实现快速网络检测

 

  启动一个iperf 客户端连接

  iperf 的另一半就是客户端,用来连接到服务器监听端口。比如我们要连接到一台叫做 s-network1.amcs.tld 的服务器,端口为5999,连接60 秒并且每5秒显示一次状态,命令行如下:

  iperf.exe -c s-network1.amcs.tld -P 1 -i 5 -p 5999 -f B -t 60 -T 1

  命令启动后,s-network1 主机被用来进行网络性能检测。与Jperf GUI 界面提供的漂亮图形不同, iperf只会根据测量参数简单的报告网络带宽状况,在本例中是以 比特为单位(-f 参数)进行带宽表示的。图B显示了远程客户端与s-network1主机间的带宽性能。

  图 B


简单的iperf命令 实现快速网络检测

 

  为了应对日常便捷应用的需求,我们可以建立一个 .bat批处理文件,届时填入服务器名称即可实现快速检测。以下为实际使用的拷屏:

C:\jperf\jperf\bin>iperf
Usage: iperf [-s|-c host] [options]
Try `iperf --help' for more information.

C:\jperf\jperf\bin>iperf --help
Usage: iperf [-s|-c host] [options]
      iperf [-h|--help] [-v|--version]

Client/Server:
 -f, --format   [kmKM]  format to report: Kbits, Mbits, KBytes, MBytes
 -i, --interval #       seconds between periodic bandwidth reports
 -l, --len      #[KM]   length of buffer to read or write (default 8 KB)
 -m, --print_mss         print TCP maximum segment size (MTU - TCP/IP header)
 -o, --output   <filename> output the report or error message to this specified file
 -p, --port     #       server port to listen on/connect to
 -u, --udp               use UDP rather than TCP
 -w, --window   #[KM]   TCP window size (socket buffer size)
 -B, --bind     <host>  bind to <host>, an interface or multicast address
 -C, --compatibility     for use with older versions does not sent extra msgs
 -M, --mss      #       set TCP maximum segment size (MTU - 40 bytes)
 -N, --nodelay           set TCP no delay, disabling Nagle's Algorithm
 -V, --IPv6Version       Set the domain to IPv6

Server specific:
 -s, --server            run in server mode
 -D, --daemon            run the server as a daemon
 -R, --remove            remove service in win32

Client specific:
 -b, --bandwidth #[KM]   for UDP, bandwidth to send at in bits/sec
                          (default 1 Mbit/sec, implies -u)
 -c, --client   <host>  run in client mode, connecting to <host>
 -d, --dualtest          Do a bidirectional test simultaneously
 -n, --num      #[KM]   number of bytes to transmit (instead of -t)
 -r, --tradeoff          Do a bidirectional test individually
 -t, --time     #       time in seconds to transmit for (default 10 secs)
 -F, --fileinput <name>  input the data to be transmitted from a file
 -I, --stdin             input the data to be transmitted from stdin
 -L, --listenport #      port to recieve bidirectional tests back on
 -P, --parallel #       number of parallel client threads to run
 -T, --ttl      #       time-to-live, for multicast (default 1)

Miscellaneous:
 -h, --help              print this message and quit
 -v, --version           print version information and quit

[KM] Indicates options that support a K or M suffix for kilo- or mega-

The TCP window size option can be set by the environment variable
TCP_WINDOW_SIZE. Most other options can be set by an environment variable
IPERF_<long option name>, such as IPERF_BANDWIDTH.


展开阅读全文
加载中
点击引领话题📣 发布并加入讨论🔥
打赏
0 评论
0 收藏
0
分享
返回顶部
顶部